Go back

ProtectGuard® WF Premium

Water and oil-repellent, stain protection with intense wet effect

ProtectGuard® WF Premium provides porous and slightly-porous material surfaces with a very intense “wet effect”, in other words, it restores and revives the original colour of surfaces.

ProtectGuard® WF Premium is traffic resistant and provides a long-lasting wet effect. ProtectGuard® WF Premium also provides protection against water, oil and stains. It provides long-term protection for all materials and prevents the main causes of deterioration such as atmospheric pollution and grease. mark, etc. It slows down the ageing of the material and makes it easier to maintain.

ProtectGuard® WF Premium is an impregnation product, the material remains permeable to air and water vapour.

  • Beading effect
  • Floors, facades
  • Coverage (1Kg = 20m2)
Advantages
  • Protection against water, oil and stains
  • Intense wet effect that restores the colour
  • Long-lasting resistance
  • Can be used on a wide range of material
  • Does not form a film, lets the material breathe
  • High performance
  • Delays ageing and makes maintenance easier
USE
  • Porous and slightly porous materials: natural stone (travertine, Bavarian stone, blue stone, marble, etc.), reconstituted stone, concrete, terracotta, etc.
  • Floors and facades
  • New or old
  • Interior or exterior
  • Recommended for patios, garage driveways, pedestrian areas, pool surrounds, facades, stairs, etc.
Back to the list
Advantages
  • Protection against water, oil and stains
  • Intense wet effect that restores the colour
  • Long-lasting resistance
  • Can be used on a wide range of material
  • Does not form a film, lets the material breathe
  • High performance
  • Delays ageing and makes maintenance easier
USE
  • Porous and slightly porous materials: natural stone (travertine, Bavarian stone, blue stone, marble, etc.), reconstituted stone, concrete, terracotta, etc.
  • Floors and facades
  • New or old
  • Interior or exterior
  • Recommended for patios, garage driveways, pedestrian areas, pool surrounds, facades, stairs, etc.

Surface preparation :

  • 1
    Apply the product to a clean, dust-free, grease-free and dry surface.
  • 2
    To remove stains and traces of pollution, use Guard Wash® or Guard Wash® Express.
  • 3
    To remove grease stains, use Net'Guard® Ultra 4 in 1.
  • 4
    To remove traces of efflorescence, laitance or grout film, use Guard Remover® Eco Efflorescence & Cement.
  • 5
    Rinse carefully until the surface is free of any trace of cleaner and let the surface dry.

Application :

  • Use the product in its pure form: do not dilute it.
  • Shake the package thoroughly before use and use the pure product: do not dilute it or mix it with another product.
  • Carry out a preliminary test on a small area.

Step 1: Apply

  • Apply a thin layer taking care to correctly apply the product (the application tool does not need to be too soaked, use the product sparingly).
    Do not overload the material; all of the product must penetrate into the surface.

Step 2: Wipe

  • After 10 minutes, carefully wipe and polish the treated material with a microfibre, lint-free cloth.
  • On large surfaces, work in zones to avoid treading on the product during wiping. Where necessary, apply a further layer to produce an even wet effect.
  • Protected drying: 24 hours.
  • Optimal efficiency reached after 7 days.

For further information, refer to the data sheet and safety sheet.

  • Application: short-haired brush or brush for acrylic varnish.

  • Wiping: microfibre, lint-free cloth.

  • 2KG

  • 5KG

  • Technical data sheet

  • Safety data sheet