Go back

ProtectGuard® Plant-based Formula

Water and oil-repellent for porous and low-porous materials. Vegetable-based formula

ProtectGuard® Plant-based Formula is a powerful vegetable-based water and oil repellent. It durably protects all porous and low-porous materials.

ProtectGuard® Plant-based Formula protects against water penetration and limits the negative effects caused by damp. It prevents penetration from soiling and greasy stains. It slows down the ageing of the material and makes it easier to maintain.

ProtectGuard® Plant-based Formula resists to funghi and limits the formation of moss and lichens. Its formulation also limits slipperiness of floors.

ProtectGuard® Plant-based Formula is a non-film forming product. It is completely colourless after application, it does not change the appearance or the nature of the treated material. It is also is fully UV ray resistant and does not yellow over time.

ProtectGuard® Plant-based Formula is 50% biosourced, vegetable-based: wheat, corn, beetroot and tree resin.

See the distributors
  • Beading effect
  • Eco-friendly
  • Floors, facades
  • Coverage (1L = 10m2)
Advantages
  • Protects against water, oil and stains
  • Biosourced formula, vegetable-based ingredients
  • Odourless
  • Lets the material breath
  • UV and frost resistant
  • Solvent-free, 90% biodegradable
USE
  • Porous and low-porous materials: natural or reconstituted stone, concrete, terracotta, coating, render, slate, travertine, marble, granite, etc.
  • Floors and facades
  • New or old
  • Internal or external
Back to the list
Advantages
  • Protects against water, oil and stains
  • Biosourced formula, vegetable-based ingredients
  • Odourless
  • Lets the material breath
  • UV and frost resistant
  • Solvent-free, 90% biodegradable
USE
  • Porous and low-porous materials: natural or reconstituted stone, concrete, terracotta, coating, render, slate, travertine, marble, granite, etc.
  • Floors and facades
  • New or old
  • Internal or external
Application
Application tools
Packaging
Technical documents

Surface preparation :

  • 1
    Apply the product to a clean, dust-free, grease-free and dry surface.
  • 2
    To remove stains and traces of pollution, use Guard Wash® or Guard Wash® Express.
  • 3
    To remove grease stains, use Net'Guard® Ultra 4 in 1.
  • 4
    To remove traces of efflorescence, laitance or grout film, use Guard Remover® Eco Efflorescence & Cement.
  • 5
    Rinse carefully until the surface is free of any trace of cleaner.

Application :

  • Use the product in its pure form: do not dilute it.
  • Shake the packaging well before use and carry out a preliminary test.
  • The material must be impregnated up to saturation in a single coat.
  • On very porous materials, apply a second coat after 15 minutes.
  • Do not spray the product, apply with a roller or a brush.
  • On vertical materials, apply from bottom to top
  • In some cases, product can leave white marks on the surface after application. Marks will disappear after complete drying. 
  • Do not overload the material, remove any excess before drying.
  • Protected drying: 24 hours.
  • Optimal efficiency reached after 7 days.

For further information, refer to the data sheet and safety sheet.

  •

    Apply using a roller or a brush.

  • 1L

  • 3L

  • 20L

  •

    Technical data sheet

  •

    Safety data sheet

Related products

Protection
ProtectGuard®
Water and oil-repellent, soiling and graffiti protection for porous materials
Discover
Protection
ProtectGuard® WF Premium
Water and oil-repellent, stain protection with intense wet effect
Discover
Protection
ProtectGuard® MG
Water/oil repellent, soiling and graffiti protection for very low porous, polished or crystallized materials
Discover
All the products