produits hydrofuges et oléofugesImperméabilisation et anti graffiti
fr  gb  us  es  de  it ru  gr

ua cn  pt  hu  nl  ro  sk  dz

AntiGraffitiGuard Permanent

PERMANENT ANTI-GRAFFITI CLEAR AND BREATHABLE COATING
PROTECTS ALL POROUS AND NON-POROUS BUILDING MATERIALS

PRODUCT DESCRIPTION

ANTIGRAFFITIGUARD  is a 2-pack anti-graffiti coating that give a durable protection for porous and non-porous materials used in the building industry: concrete, lime coatings, terra cotta, natural and artificial stones, timber, painted substrates…

It can be used inside and outside, on new and refurbished surfaces.
Its anti-graffiti properties make it particularly suitable for vertical surfaces (facades, walls…).

It can also be used on horizontal surfaces as a pedestrian coating but the applicator must apply a test application to ensure ANTIGRAFFITIGUARD is acceptable.

The application of ANTIGRAFFITIGUARD can slightly modify the substrate colour. It is therefore necessary to do a test on a hidden or non-too visible part of the substrate before progressing.

CHARACTERISTICS

  • Anti-graffiti protection
  • Protection against hydrocarbons, grease and organic stains
  • Protection against chemical and water-soluble biological agents. Can be applied on both new concrete and old surfaces
  • The product gives the substrate a low satin finish
  • Good resistance to wear and tear and scratches
  • Excellent UV resistance
  • Good adhesion to concrete.
  • Non-hazardous and non-toxic
  • Easy to use
  • Non-flammable

COVERAGE PER LITRE

Coverage depends on the porosity of the material. The figures below are approximate and should be used only as a general guideline:
6 to 10 m² / litre

USAGE

  • Shake well before use. Ensure all components are thoroughly dispersed
  • Add the hardener to ANTIGRAFFITIGUARD product base. Mix carefully for 15 minutes using an electrical mixer until a homogeneous mix  is obtained
  • The hardener quantity has been precisely equated to the ANTIGRAFFITIGUARD product base. The entire hardener must be mixed into the product base. It is important not to put more product basis or hardener
  • The prepared mix can after be used for upto 8 hours (when the air temperature is less than 25°C).
  • Once the hardener has been added to the base, let it stand for half an hour and mix the product again for 1 minute
  • ANTIGRAFFITIGUARD can be applied with a HVLP low pressure or pneumatic spray. Brush application is also suitable.
  • The product must be applied onto a dry and clean substrate
  • On porous substrate, it is recommended to apply a first coat of ANTIGRAFFITIGUARD which has been diluted 10% with water - w/w. Subsequent coats must be applied undiluted, and immediately the first coat is dry to touch.
  • The conditions of substrate application and preparation must satisfy DTU 59.1. Pay particular attention to surface preparation before application as this plays a fundamental role to the final look and performance of the coating, especially the adhesion of ANTIGRAFFITIGUARD to the substrate.

PACKAGING

1L, 5L, 10L, 25L
Respectful of Man and Environment.
To obtain the technical sheet, contact us with the contact form and do not forget to fill all the field.


SECURITY FACT SHEET    >>>SECURITY FACT SHEET
To see our references, click here : References
Make a simulation to obtain the requested quantity of products litres by choosing a product, the kind of material to be treated and by defining the number of square metres of the surface area to be treated.

Document and photos are not contractual .
We are not responsible of a bad use of our products.
It is indispensable to proceed to preliminary attempts.

Guard Industrie SAS 300 000 Euros 7 rue Gutenberg 93108 - MONTREUIL CEDEX - FRANCE
Tel : +33 (0)1 55 86 17 60 - Fax. +33 (0)1 48 58 16 89

copyright ©guardindustrie.com - tous droits réservés